NFPA 70E (electrical safety in the workplace)
The consensus standard for electrical safety work practices: energized-work justification, approach boundaries, arc-flash risk assessment, PPE categories, and establishing an electrically safe work condition. Fab facilities electricians and many equipment technicians who work on tool power are asked for current 70E training.
- Who issues it
- National Fire Protection Association (NFPA) publishes the standard; training comes from many providers. Issuer site
- Roles that ask for it
- Fab facilities electricians, Equipment technicians, UPW / gas / subfab technicians
- Required or preferred
- Commonly required for anyone who works on or near energized electrical equipment.
OSHA 10 / OSHA 30
10-hour and 30-hour Outreach Training Program courses covering jobsite hazard recognition. OSHA 30 is aimed at supervisors and people with safety responsibility. Construction and tool-install phases at new fabs often list these explicitly.
- Who issues it
- Delivered by OSHA-authorized Outreach trainers; completion cards are issued through the program. Issuer site
- Roles that ask for it
- All fab facilities and equipment roles, Construction and tool-install teams
- Required or preferred
- Often preferred for operations roles; frequently required on construction, hook-up, and tool-install sites.
EPA Section 608 (Type I, II, III, Universal)
EPA technician certification required to maintain, service, repair, or dispose of equipment that could release refrigerants. Fab HVAC and facilities technicians who work chillers, process cooling, or cleanroom air handlers are commonly asked for Universal certification.
- Who issues it
- U.S. Environmental Protection Agency, through EPA-approved certifying organizations. Issuer site
- Roles that ask for it
- Fab HVAC / controls technicians, Fab facilities technicians
- Required or preferred
- Required by law for refrigerant work; Universal is the version most mechanical postings list.
Journeyman / master electrician license
A state or local license to perform electrical work. Requirements, reciprocity, and whether a license is needed for in-house facilities work (versus construction) vary by state and jurisdiction. Arizona, Texas, Ohio, and New York each have their own rules.
- Who issues it
- State or local licensing boards. Issuer site
- Roles that ask for it
- Fab facilities electricians, Electrical leads
- Required or preferred
- Commonly required for electrician titles; check the state where the fab is.
Lockout/tagout (LOTO) and arc-flash training
Training on controlling hazardous energy before servicing equipment, and on arc-flash hazards and PPE. LOTO is required by OSHA standard 29 CFR 1910.147 for covered work. In a fab this applies to process tools, pumps, abatement, and facilities equipment.
- Who issues it
- OSHA sets the rule; employers and training providers deliver the training. Issuer site
- Roles that ask for it
- All hands-on fab, equipment, and facilities roles
- Required or preferred
- Expected. Most employers train on their own LOTO program at onboarding.
Confined space entry training
Training on permit-required confined spaces under OSHA 29 CFR 1910.146: atmospheric testing, attendants, rescue, and entry permits. Fab facilities work often includes tanks, pits, exhaust plenums, and UPW or chemical rooms that fall under this rule.
- Who issues it
- OSHA sets the rule; employers and training providers deliver the training. Issuer site
- Roles that ask for it
- Fab facilities technicians, UPW / gas / chemical handling technicians
- Required or preferred
- Required for covered entry work; usually delivered by the employer.
Hazard communication (HazCom) and chemical safety
OSHA’s Hazard Communication Standard (29 CFR 1910.1200) covers labels, safety data sheets, and training on hazardous chemicals. Fabs use process chemicals, specialty gases, and slurries that make this training a baseline, not a bonus.
- Who issues it
- OSHA sets the rule; employers deliver site-specific training. Issuer site
- Roles that ask for it
- Equipment technicians, Process engineers, Fab facilities technicians
- Required or preferred
- Expected for almost every cleanroom and subfab role. Site-specific chemical training is added after hire.
Respiratory protection training
Training and medical clearance under OSHA 29 CFR 1910.134 for people who wear respirators, including PAPR units used around certain chemicals or during some maintenance tasks. Fit testing is part of a complete program.
- Who issues it
- OSHA sets the rule; employers run the program. Issuer site
- Roles that ask for it
- Equipment technicians, Fab facilities technicians, Some process engineering roles
- Required or preferred
- Required when the job includes respirator use; usually completed during onboarding.
ISA CCST (Certified Control Systems Technician)
A three-level technician credential covering control systems installation, calibration, loop checking, and troubleshooting. Useful for fab facilities controls work on UPW, HVAC, gas detection, and process-exhaust systems.
- Who issues it
- International Society of Automation (ISA). Issuer site
- Roles that ask for it
- Fab HVAC / controls technicians, Instrumentation technicians
- Required or preferred
- Preferred, rarely required. Experience on the systems usually matters more.
High-purity / orbital welding credentials
Credentials and documented procedure qualifications for orbital and high-purity welding used on UPW, process-gas, and clean process piping. AWS Certified Welder and ASME BPE-related qualifications are the names most often seen. Exact requirements are set by the owner and the piping specification, not by a single universal card.
- Who issues it
- American Welding Society (AWS) and owner/contractor welding programs; ASME publishes the Bioprocessing Equipment (BPE) standard. Issuer site
- Roles that ask for it
- UPW and process-piping technicians, Fab facilities mechanical technicians
- Required or preferred
- Often required for dedicated high-purity piping work; preferred on broader facilities teams.
Professional Engineer (PE) license
A state license for engineers who offer services to the public or take responsible charge of engineering work. Some senior process, facilities, or equipment engineering roles prefer a PE; many industry process-engineering seats do not require one.
- Who issues it
- State licensing boards. NCEES administers the FE and PE exams used by most states. Issuer site
- Roles that ask for it
- Process engineers, Fab facilities engineers
- Required or preferred
- Preferred on some senior or facilities-engineering roles; not usually required for module process engineers.
ASQ Six Sigma Green Belt / Black Belt
Process-improvement credentials covering DMAIC, statistical process control, and structured problem solving. Process engineers already use these tools daily; a Green or Black Belt can help career changers show they have the method, not only the title.
- Who issues it
- American Society for Quality (ASQ) is a widely recognized issuer; employers also accept internal or other accredited belts. Issuer site
- Roles that ask for it
- Process engineers, Equipment engineers, Yield and quality engineers
- Required or preferred
- Preferred, rarely required. On-the-job SPC and excursion work usually weighs more.
Cleanroom protocol / ISO 14644 (concept)
ISO 14644 is the family of standards that classifies air cleanliness and related cleanroom practices. Gowning, particle discipline, and material transfer are usually taught by the employer, not by a public license. Knowing the basics helps career changers from industrial or facilities work.
- Who issues it
- International Organization for Standardization (ISO) publishes the standard. Training is typically employer-provided. Issuer site
- Roles that ask for it
- Every cleanroom role
- Required or preferred
- Experience is preferred. Most fabs train gowning and protocol in orientation.
SEMI S2 / S8 (concept)
SEMI S2 is a widely used environmental, health, and safety guideline for semiconductor manufacturing equipment. SEMI S8 covers ergonomics. These are equipment and design guidelines, not people certifications. Technicians and engineers are often expected to work in ways that follow them.
- Who issues it
- SEMI. Issuer site
- Roles that ask for it
- Equipment technicians, Equipment and process engineers, Fab facilities technicians
- Required or preferred
- Knowledge is preferred; there is no single “SEMI certificate” most employers require of technicians.
Descriptions summarize each issuer’s public information and common posting language. They are not legal or licensing advice; requirements vary by employer and state.